LITON ENEN

Corrosion inhibitor in a heating system: how to protect it from rust and deposits

Corrosion and deposits build up quietly in a central heating system until the radiators heat less and the boiler has to work harder. We explain what a corrosion inhibitor does, how it differs from a descaler and from flushing, and how to protect the system so it lasts longer without failures.

Choose a product for the job

Where corrosion in a heating system comes from

In a closed heating system the same water circulates again and again, and with it the last traces of oxygen and dissolved salts. That is enough for rust to start forming on the metal parts and for sludge and scale to collect at the bottom of the radiators. Over time the deposits narrow the flow, radiators turn cold at the top, and the pump and boiler have to work harder.

The effect is twofold. The system heats worse and uses more energy, and at the same time it wears out faster, because corrosion weakens the parts from the inside. Protecting against corrosion is therefore not a luxury but a way to a longer-lasting system that is cheaper to run.

What a corrosion inhibitor is and how it works

A corrosion inhibitor is a product added to the water in the system. It forms a thin protective layer on the metal surface and slows down the reactions that lead to rusting, and it also limits the build-up of deposits. In practice it protects the radiators, pipes, pump and boiler from the inside, where you cannot reach mechanically. In the LITON range this is the HYDROPROX corrosion inhibitor.

An inhibitor does not repair what has already been damaged, but it stops the process from going further. It therefore gives the most in a system that is clean, and it is best used right after cleaning the system or when commissioning a new one.

Inhibitor, descaler, flushing — what is for what

These three things are often confused, yet they do different jobs and work best in the right order.

  • Flushing and cleaning removes sludge, mud and loose deposits from the system. A cleaning product for heating systems is used for this.
  • A descaler dissolves scale and hard deposits that narrow the flow and insulate the radiators. A descaler for heating systems works here.
  • A corrosion inhibitor protects the already cleaned system against further corrosion and deposits.

Tip

The right order is to clean and flush the system first, and only then add the inhibitor. Protecting a dirty system makes much less sense, because the deposits stay inside.

When it is worth using a corrosion inhibitor

  • When commissioning a new system, to protect it from the start.
  • After flushing or cleaning an old system, as a protective layer.
  • When radiators heat unevenly or are cold at the top, which often points to sludge and corrosion.
  • When rusty, dark water comes out of the system.

How to use a corrosion inhibitor step by step

  1. 1
    Clean the system first. Flush an old system and remove scale if needed, so the inhibitor protects clean metal and not a layer of deposit.
  2. 2
    Dose according to the label. The amount of product depends on the system volume. The correct proportions are given on the label of the specific product.
  3. 3
    Introduce the product into the circuit. Add the inhibitor to the water in the system and let it spread through the whole circuit according to the instructions.
  4. 4
    Top up after adding water. After a larger top-up of water it is worth restoring the inhibitor level, so the protection stays complete.

Note

Do not mix different products together at once without checking that they are compatible. Follow the dosing and the order given on the product label.

The most common mistakes when protecting a heating system

  • Adding the inhibitor to a dirty system without flushing it first.
  • Skipping the descaling step when there is already hard scale in the system.
  • Dosing by eye instead of by system volume and the label.
  • Forgetting to top up the inhibitor after a larger addition of water.

Frequently asked questions

What is a corrosion inhibitor?

It is a product added to the water in the system that forms a protective layer on the metal and slows down corrosion and the build-up of deposits. It protects the radiators, pipes, pump and boiler from the inside.

How does a corrosion inhibitor differ from a descaler?

A descaler removes scale and hard deposits that are already in the system. A corrosion inhibitor works preventively, protecting the cleaned metal from further corrosion. It is best to use them in order: cleaning first, then protection with the inhibitor.

When should I use a corrosion inhibitor in a heating system?

Best when commissioning a new system or after flushing and cleaning an old one. It is also worth considering when radiators heat unevenly or rusty water comes out of the system.

How do I dose a corrosion inhibitor?

The amount depends on the system volume. The exact proportions and the way to introduce it into the circuit are given on the label of the specific product, so follow it instead of dosing by eye.

Is a corrosion inhibitor suitable for every system?

Products of this type are intended for heating systems and closed circuits. Use in another kind of installation should be checked on the data sheet of the specific product.

Recommended products

HYDROPROX corrosion inhibitor

HYDROPROX

corrosion inhibitor

4.99(246)
€50.00
In Stock
IZOMARK corrosion inhibitor

IZOMARK

corrosion inhibitor

4.97(248)
€48.00
In Stock
ESANDOL pro line protective coating corrosion inhibitor

ESANDOL

pro line protective coating corrosion inhibitor

4.82(323)
€89.00
In Stock
HYDROPROX liquid lubricant for ecobean boilers

HYDROPROX

liquid lubricant for ecobean boilers

5.00(296)
€50.00
In Stock